Analog Devices Inc. ADIS16334/PCBZ

Overview

ADIS16334/PCBZ from Analog Devices is a low-profile, six-degree-of-freedom inertial sensor evaluation board featuring integrated triaxial gyroscope (±300°/sec range), triaxial accelerometer (±5 g), 330 Hz bandwidth, factory-calibrated bias/sensitivity/alignment, and SPI interface. It enables rapid prototyping of motion sensing in robotics, navigation, and platform stabilization systems.

For engineers reviewing the ADIS16334/PCBZ datasheet, ADIS16334/PCBZ pinout, ADIS16334/PCBZ application, or ADIS16334/PCBZ equivalent, this page delivers verified mechanical interface details, confirmed SPI timing constraints (≤2 MHz SCLK), validated breakout functionality, and direct compatibility with ADIS16334 inertial sensor module operation-no configuration required at power-up.

Technical Context

The ADIS16334/PCBZ is a dedicated evaluation platform for the ADIS16334 inertial sensor module, providing standardized 0.1" header access to all 20 pins-including SPI (CS, SCLK, DIN, DOUT), digital I/O (DIO1–DIO4), power (VCC, GND), and reset (RST). It supports full-duplex SPI communication in Mode 3 (CPOL=1, CPHA=1) at up to 2 MHz for single reads and 1 MHz for burst reads.

It exposes the ADIS16334's autonomous sampling architecture (819.2 SPS default), self-test capability, programmable alarms, and temperature-compensated calibration data without requiring external configuration commands. The board implements no signal conditioning or level-shifting-digital I/O signals are 5 V tolerant and driven from an internal 3.3 V supply, matching ADIS16334's native logic interface.

Key Specifications

Availability

ADIS16334/PCBZ is available at Aetrix Electronics and suitable for robotics development, inertial navigation validation, and industrial platform control prototyping requiring stable component supply and immediate hardware access to ADIS16334 sensor outputs.

Supply support for ADIS16334/PCBZ includes scheduled delivery planning, volume procurement assistance, BOM continuity management, traceable sourcing, and lifecycle availability coordination for OEM customers, industrial embedded developers, connected-device designers, and electronics production programs.

Manufacturer

Analog Devices, Inc. is a global leader in high-performance analog, mixed-signal, and digital signal processing semiconductors, headquartered in Norwood, MA.

The ADIS16334/PCBZ belongs to Analog Devices' iSensor® evaluation board family, designed specifically to accelerate integration of factory-calibrated inertial modules into motion-critical applications without custom PCB design.

FAQ

What is the ADIS16334/PCBZ used for?

The ADIS16334/PCBZ is an evaluation board that provides physical and electrical access to the ADIS16334 six-degree-of-freedom inertial sensor module. It enables engineers to quickly validate sensor performance, develop SPI firmware, and integrate motion data into host systems without designing custom carrier hardware. The ADIS16334/PCBZ does not contain active circuitry beyond passive routing and header connections-it functions solely as a breakout interface for the ADIS16334 module.

Does the ADIS16334/PCBZ include the ADIS16334 sensor module?

Yes-the ADIS16334/PCBZ ships with the ADIS16334 inertial sensor module pre-mounted and soldered to the board. The module is a 24 mm × 33 mm × 11 mm surface-mount device with a 20-pin connector interface, and the ADIS16334/PCBZ provides direct 0.1" header access to all its pins, including SPI, DIOx, power, and reset lines.

What SPI settings are required to communicate with the ADIS16334 via the ADIS16334/PCBZ?

To communicate with the ADIS16334 via the ADIS16334/PCBZ, configure the host SPI master for Mode 3 (CPOL = 1, CPHA = 1), MSB-first transmission, 16-bit word length, and SCLK ≤ 2 MHz for single-register reads or ≤ 1 MHz for burst reads. Chip select (CS) must be asserted low before each transaction, and data is sampled on SCLK falling edge (DOUT) and latched on rising edge (DIN), per ADIS16334/PCBZ pin mapping.

Can the ADIS16334/PCBZ operate standalone without external components?

Yes-the ADIS16334/PCBZ requires only a regulated 4.75 V to 5.25 V supply applied to its VCC and GND headers to power the ADIS16334 module. No external resistors, capacitors, or level shifters are needed. The ADIS16334/PCBZ supports autonomous operation: it begins sampling at 819.2 SPS within 180 ms of power-up and asserts DIO1 as a data-ready indicator without host intervention.

Is the ADIS16334/PCBZ compatible with other iSensor evaluation tools?

Yes-the ADIS16334/PCBZ uses standard 0.1" pin spacing and follows Analog Devices' iSensor evaluation board layout conventions, enabling direct use with the EVAL-ADIS system, System Development Platform (SDP), and PC-based tools like the iSensor Evaluation Software. Its pinout matches the ADIS16334 module datasheet (Rev. D), ensuring interoperability with existing firmware examples and configuration utilities for the ADIS16334.