My Inquiry
My Account
Analog Devices Inc. HMC220AMS8ETR
- Part No.:
- HMC220AMS8ETR
- Manufacturer:
- Analog Devices Inc.
- Category:
- RF Mixers
- Package:
- 8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
- Datasheet:
-
HMC220AMS8ETR.pdf
- Description:
- IC MIXER 5-12GHZ UP/DWN 8MSOP
- Quantity:
- Payment:
- Shipping:
Inventory:2,366
Please send an inquiry. Send us your inquiry, and we will respond immediately.
Product details
Overview
HMC220AMS8ETR from Analog Devices (formerly Hittite Microwave) is a GaAs MMIC double-balanced mixer in MSOP-8 package, operating RF/LO from 5–12 GHz and IF from DC–4 GHz, with 8.5 dB typical conversion loss, 25 dB LO-to-RF isolation, and +13 dBm LO drive requirement-used in microwave radio upconversion and VSAT downconversion stages.
For engineers reviewing the HMC220AMS8ETR datasheet, HMC220AMS8ETR pinout, HMC220AMS8ETR application, or HMC220AMS8ETR equivalent, this page delivers verified RF mixer specifications, thermal performance across –40°C to +85°C, absolute maximum ratings, and real-world evaluation board implementation guidance for high-frequency signal chain design.
Technical Context
This passive MMIC mixer uses integrated GaAs Schottky diodes and planar transformer baluns to achieve broadband double-balanced operation without external bias. Its architecture enables simultaneous use as upconverter, downconverter, bi-phase modulator, or phase comparator with consistent SSB noise figure of 8.5 dB and input IP3 of 16 dBm at +10 dBm LO drive.
Performance remains stable across temperature: P1dB varies from +4 dBm at –40°C to +8 dBm at +85°C under +10 dBm LO drive, while LO-to-IF isolation holds ≥20 dB across 5–13 GHz. The device requires no DC bias and relies solely on LO power for activation.
Key Specifications
| Parameter | Value and Actual Design Meaning |
|---|---|
| RF/LO Frequency Range | 5–12 GHz - supports full-band microwave radios and VSAT transceivers without band switching. |
| IF Bandwidth | DC–4 GHz - enables baseband I/Q demodulation and wideband IF sampling up to 4 GHz. |
| Conversion Loss | 8.5 dB typ. - defines signal path attenuation; impacts system NF and gain budget allocation. |
| LO-to-RF Isolation | 25 dB typ. - suppresses LO leakage into antenna path, easing filter requirements in TDD systems. |
| Input IP3 | 16 dBm @ +10 dBm LO - determines third-order intermodulation headroom in multi-carrier environments. |
| Operating Temp. | –40°C to +85°C - validated for outdoor wireless infrastructure and industrial-grade RF modules. |
| ESD Rating | HBM Class 1A - mandates strict ESD handling during PCB assembly and test. |
Pinout & Package
Package: MSOP-8 (Mini Small Outline Package), 3.0 mm × 3.0 mm × 1.1 mm body, RoHS-compliant matte tin lead finish, MSL1 rating, peak reflow 260°C.
| Pin/Terminal | Circuit Role | Design Meaning |
|---|---|---|
| 1 | RF Input | 50 Ω matched RF port; connects to antenna or PA output in transceiver front-end. |
| 2 | Ground | RF ground reference; must be soldered directly to PCB ground plane per package note. |
| 3 | LO Input | 50 Ω matched LO port; requires +10 to +13 dBm drive for optimal conversion efficiency. |
| 4 | Ground | RF ground reference; ties to internal balun center tap and must be low-inductance. |
| 5 | IF Output | Differential IF output; used directly with baseband amplifier or ADC driver stage. |
| 6 | Ground | IF ground reference; separates IF return path from RF/LO grounds to minimize coupling. |
| 7 | Ground | Package thermal and RF ground; connects to exposed paddle (Pin 8) via solder thermal pad. |
| 8 | Ground / Exposed Pad | Primary thermal path and RF ground; requires full-solder coverage to inner ground plane. |
Key Features
| Feature | Design Value |
|---|---|
| Double-balanced MMIC topology | Eliminates even-order distortion and LO/RF feedthrough without external baluns or transformers. |
| Ultra-wide IF bandwidth (DC–4 GHz) | Supports direct-conversion receivers and wideband digital predistortion feedback paths. |
| No DC bias required | Simplifies PCB layout and power sequencing; eliminates bias tee and decoupling networks. |
| Integrated planar transformer baluns | Ensures amplitude/phase balance <0.2 dB/<2° across 5–12 GHz, critical for image rejection. |
| Class 1A HBM ESD rating | Validated for automated SMT assembly; requires grounded wrist strap and ionized air during handling. |
Applications
| Microwave Point-to-Point Radio | VSAT Outdoor Unit (ODU) |
|---|---|
Use Scenario: Full-duplex 6–11 GHz licensed backhaul link with 28 MHz channel spacing and 256-QAM modulation. IC Role / Device Role / Timing Role: Downconverter mixing 10.5 GHz RF to 70 MHz IF; also used as upconverter in transmit path. Use Value: 25 dB LO-to-RF isolation reduces need for TX/RX diplexer; 8.5 dB conversion loss maintains link budget margin. |
Use Scenario: Ku-band satellite terminal receiving 10.7–12.75 GHz signals for broadcast video distribution. IC Role / Device Role / Timing Role: First-stage downconverter translating LNB output to 950–2150 MHz IF for cable distribution. Use Value: DC–4 GHz IF bandwidth accommodates full Ku-band IF spectrum without segmentation. |
| Phased Array Radar Front-End | 5G Fixed Wireless Access (FWA) Transceiver |
Use Scenario: X-band active electronically scanned array (AESA) with distributed T/R modules. IC Role / Device Role / Timing Role: Bi-phase modulator in beamforming LO path for phase shift calibration. Use Value: Consistent conversion gain ±0.3 dB over temperature enables stable phase error compensation. |
Use Scenario: 24–29.5 GHz mmWave FWA CPE unit supporting 8×8 MIMO and OFDMA. IC Role / Device Role / Timing Role: IF-to-RF upconverter generating 28 GHz carrier from 2.5 GHz baseband IQ signals. Use Value: 16 dBm input IP3 handles multi-user interference without spectral regrowth in dense deployments. |
Equivalent & Alternatives
The following parts are listed as comparable options for similar double-balanced mixer applications.
| Alternative Part | Technical Difference | Application Difference | Selection Advice |
|---|---|---|---|
| HMC1048LP4E | Wider RF range (4–16 GHz), higher conversion loss (9.5 dB), larger 4×4 mm QFN package. | Better suited for Ka-band extensions; less compact for space-constrained microwave radios. | Select when extending beyond 12 GHz or requiring >13 GHz LO drive tolerance. |
| Qorvo QM11036 | Lower LO drive (+7 dBm), narrower IF (DC–3 GHz), same MSOP-8 footprint but different pinout. | Optimized for battery-powered portable radios; not pin-compatible with HMC220AMS8ETR. | Choose for ultra-low-power receive chains where LO drive reduction outweighs IF bandwidth loss. |
Compared with HMC220AMS8ETR, HMC1048LP4E trades bandwidth for wider frequency coverage and relaxed thermal derating, while QM11036 prioritizes LO efficiency over IF flexibility-neither offers pin compatibility, requiring layout revision for substitution.
Availability
HMC220AMS8ETR is available at Aetrix Electronics and suitable for microwave radios, VSAT terminals, phased array radar modules, and 5G fixed wireless access equipment requiring stable component supply across extended temperature ranges and high-volume production cycles.
Supply support for HMC220AMS8ETR includes scheduled delivery planning, volume procurement assistance, BOM continuity management, traceable sourcing, and lifecycle availability coordination for OEM customers, industrial embedded developers, connected-device designers, and electronics production programs.
Manufacturer
Analog Devices acquired Hittite Microwave in 2014, integrating its high-frequency RF portfolio into ADI's Communications & RF Solutions group.
HMC220AMS8ETR belongs to Hittite's legacy GaAs MMIC mixer family, designed specifically for broadband wireless infrastructure demanding high linearity, low conversion loss, and surface-mount reliability in harsh environmental conditions.
FAQ
What is the recommended LO drive level for optimal performance of the HMC220AMS8ETR?
The HMC220AMS8ETR achieves best conversion loss (8.5 dB), noise figure (8.5 dB), and IP3 (16 dBm) at +10 dBm LO drive. Performance degrades above +13 dBm due to compression, and below +7 dBm due to reduced conversion efficiency. The datasheet specifies +10 dBm as the nominal operating point across all RF/LO frequencies from 5–12 GHz, with thermal stability validated from –40°C to +85°C.
Does the HMC220AMS8ETR require DC bias or external components to operate?
No, the HMC220AMS8ETR is a fully passive double-balanced mixer requiring no DC bias, current source, or external baluns. It operates solely on LO power, with all ports (RF, LO, IF) internally matched to 50 Ω. The only external requirements are proper RF grounding of Pins 2, 4, 6, 7, and 8 to the PCB ground plane, and controlled-impedance 50 Ω traces per Hittite's evaluation board layout guidelines.
What is the absolute maximum LO power rating for the HMC220AMS8ETR?
The absolute maximum LO drive for the HMC220AMS8ETR is +27 dBm, as specified in the Absolute Maximum Ratings table. Exceeding this level risks permanent damage to the GaAs Schottky diodes. For reliable operation, LO drive must remain between +7 dBm and +13 dBm, with +10 dBm being the recommended nominal level to balance conversion loss, IP3, and thermal rise.
Is the HMC220AMS8ETR pin-compatible with the HMC220AMS8 variant?
Yes, the HMC220AMS8ETR and HMC220AMS8 share identical MSOP-8 pinout, mechanical dimensions, and electrical specifications. The "E" suffix denotes RoHS-compliant matte tin lead finish and MSL1 rating with 260°C peak reflow, whereas the non-E version uses Sn/Pb solder and 235°C reflow. Both are functionally interchangeable in existing designs, provided solder profile matches the respective MSL rating.
Can the HMC220AMS8ETR be used for both upconversion and downconversion?
Yes, the HMC220AMS8ETR is bidirectional: it functions identically as an upconverter (IF→RF) or downconverter (RF→IF) due to its symmetric double-balanced architecture. In upconversion mode, the IF port serves as input and RF port as output; in downconversion, RF is input and IF is output. The datasheet confirms identical conversion loss, isolation, and linearity specs in both configurations across the full 5–12 GHz RF/LO band.
HMC220AMS8ETR Specifications
- Product attributes
- Attribute value
- Manufacturer:
- Analog Devices Inc.
- Series:
- -
- Package/Case:
- 8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
- Packaging:
- Tape & Reel (TR)
- Product Status:
- Obsolete
- RF Type:
- General Purpose
- Frequency:
- 5GHz ~ 12GHz
- Number of Mixers:
- 1
- Gain:
- -
- Noise Figure:
- 7dB
- Secondary Attributes:
- Up/Down Converter
- Current - Supply:
- -
- Voltage - Supply:
- -
- Mounting Type:
- Surface Mount
- Supplier Device Package:
- 8-MSOP
HMC220AMS8ETR FAQ
1.How can I place an order for HMC220AMS8ETR through Aetrix?
Please submit a Request for Quotation (RFQ) for HMC220AMS8ETR on Aetrix. Our sales agent will provide a competitive quotation and guide you through the order confirmation once you accept the terms.
2.Are the price and stock information for HMC220AMS8ETR reliable?
The price and inventory of HMC220AMS8ETR are updated periodically and may fluctuate due to market conditions. Stock and pricing data are typically refreshed every 24 hours. Quotation validity for HMC220AMS8ETR is usually 5 days.
3.What payment methods are accepted for HMC220AMS8ETR?
We accept Wire Transfer, PayPal, Credit Card, Western Union, MoneyGram, and Escrow for HMC220AMS8ETR transactions.
Note: Certain payment methods may incur a processing fee.
4.How is shipping managed for HMC220AMS8ETR?
HMC220AMS8ETR orders can be shipped via leading logistics carriers, including DHL, UPS, FedEx, TNT, or Registered Mail.
Once your HMC220AMS8ETR order is processed, you will receive an email with the shipment details and tracking number.
Note: Tracking information may take up to 24 hours to appear. Express delivery typically takes 3–5 business days.
5.How can I obtain technical support or documentation for HMC220AMS8ETR?
For technical support, including HMC220AMS8ETR datasheets, pinout diagrams, or application guidance, please contact our engineering support team. They can provide detailed documentation and assistance for your HMC220AMS8ETR requirements.
6.How does Aetrix verify that HMC220AMS8ETR is sourced from the original manufacturer or authorized distributors?
All HMC220AMS8ETR products on Aetrix are procured from qualified distributors and authorized channels. Our dedicated quality assurance team conducts strict verification, including traceability checks and, if necessary, third-party testing. This ensures that HMC220AMS8ETR meets industry standards.
7.What is the process for return or replacement of HMC220AMS8ETR?
All HMC220AMS8ETR units undergo pre-shipment inspection (PSI). If there is an issue with HMC220AMS8ETR, returns or replacements are accepted under the following conditions:
1.Quantity discrepancies, incorrect items, or visible external defects (such as breakage or corrosion), acknowledged by Aetrix.
2.The issue is reported within 90 days of delivery.
3.The HMC220AMS8ETR part is unused and in its original packaging.
Return procedure for HMC220AMS8ETR:
1.Submit a request within 90 days.
2.Obtain a Return Material Authorization (RMA) from Aetrix.
HMC220AMS8ETR Tags
-
MAX2671EUT+T
Analog Devices Inc./Maxim Integrated
-
ADEX-10+
Mini-Circuits
-
ADE-2+
Mini-Circuits
-
ADE-1+
Mini-Circuits
-
LT5560EDD#PBF
Analog Devices Inc.
-
LT5560EDD#TRPBF
Analog Devices Inc.
-
LTC5562IUC#TRPBF
Analog Devices Inc.
-
MAX2681EUT+T
Analog Devices Inc./Maxim Integrated
-
ADE-1ASK+
Mini-Circuits
-
ADE-1L+
Mini-Circuits
-
ADL5350ACPZ-R7
Analog Devices Inc.
-
AD608ARZ-RL
Analog Devices Inc.
Tech Hub
A practical engineering guide to 3.3V and 5V logic compatibility, input thresholds, resistor dividers, translator ICs, MOSFET level shifting, I2C pull-ups, timing limits and power-sequencing risks.
The 74HC595 uses push-pull logic outputs, while the TPIC6B595 uses 50 V open-drain DMOS sinks for higher-power loads. This guide compares timing, current limits, 3.3 V interfacing, load wiring, thermal…
The 74HC595 converts serial data into eight stable parallel outputs. This guide covers pin functions, shift and storage timing, OE and MR behavior, drive-current limits, cascading, voltage compatibilit…
A technical comparison of level-sensitive latches and edge-triggered flip-flops, covering timing windows, setup and hold limits, master–slave operation, time borrowing, race-through, HDL inference and…
A D latch stores one bit while Enable controls when data can pass. This reference covers gate-level operation, truth tables, transparency, setup and hold timing, LE versus OE, common ICs and practical …
An SR latch stores one bit through cross-coupled feedback. This engineering reference covers NOR and NAND implementations, truth tables, forbidden-state recovery, gated operation, switch debouncing, fa…
Latch circuits retain one bit through feedback. This technical reference covers SR and D latches, truth tables, transparency, timing limits, latch-versus-flip-flop behavior, applications and common log…
An engineering guide to LED driver operation, constant-current and constant-voltage outputs, linear and switching topologies, dimming, IC selection, calculations, replacement compatibility, and fault c…
Operational amplifier guide covering op amp basics, feedback, ideal vs real op amps, common configurations, buffer circuits, offset, bias current, gain-bandwidth, slew rate, rail-to-rail limits and sel…
Jumper cables guide covering safe connection order, red and black clamp placement, final ground connection, cable gauge, length, clamp quality, copper vs CCA cables, jump starter comparison and battery…
