My Inquiry
My Account
Monolithic Power Systems Inc. MPQ2013AGG-33-Z
- Part No.:
- MPQ2013AGG-33-Z
- Manufacturer:
- Monolithic Power Systems Inc.
- Package:
- 6-VDFN Exposed Pad
- Datasheet:
-
MPQ2013AGG-33-Z.pdf
- Description:
- IC REG LINEAR 3.3V 150MA 6QFN
- Quantity:
- Payment:
- Shipping:
Inventory:4,558
Please send an inquiry. Send us your inquiry, and we will respond immediately.
Product details
Overview
MPQ2013AGG-33-Z from Monolithic Power Systems is a 40V-input, 150mA AEC-Q100 Grade 1 qualified linear regulator in QFN-6 (2mm×2mm) package, delivering fixed 3.3V output with ±4% accuracy at 150mA load and 620mV dropout. It features 3.3µA quiescent current, operates from −40°C to +150°C junction temperature, and supports ultra-low-power automotive microcontrollers and battery-powered sensors.
For engineers reviewing the MPQ2013AGG-33-Z datasheet, MPQ2013AGG-33-Z pinout, MPQ2013AGG-33-Z application, or MPQ2013AGG-33-Z equivalent, this page provides verified electrical parameters, thermal shutdown behavior, EN threshold voltages, FB reference stability, and validated fixed-output design context for automotive-grade power rail selection.
Technical Context
The MPQ2013AGG-33-Z uses a PMOS pass transistor architecture enabling low dropout operation across its 2.5V–40V input range. Its internal feedback network fixes VOUT at 3.3V by referencing a stable 1.215V bandgap voltage at the FB pin, with no external resistor divider required.
Control logic integrates thermal shutdown (150°C trip, 20°C hysteresis) and current limiting (160–400mA peak), while the EN pin provides precise enable/disable control via 1.26V falling and 1.48V rising thresholds. GND and exposed pad must be connected to the same ground plane for thermal and electrical integrity.
Key Specifications
| Parameter | Value and Actual Design Meaning |
|---|---|
| Input Voltage Range | 2.5V to 40V - supports direct connection to 12V/24V automotive batteries and industrial rails without pre-regulation. |
| Output Voltage | Fixed 3.3V ±4% - specified over full temperature and load range for QFN-6 package; eliminates need for external feedback resistors. |
| Quiescent Current | 3.3µA typical - enables >10-year battery life in always-on sensor nodes powered by coin cells or Li-SOCl₂. |
| Dropout Voltage | 620mV at 150mA - allows regulation down to VIN = 3.92V, critical for cold-cranking scenarios in automotive ECUs. |
| Thermal Shutdown | 150°C junction trip with 20°C hysteresis - protects against sustained overload or poor PCB copper area without latch-up. |
| Enable Threshold | EN falling threshold 1.26V, rising threshold 1.48V - ensures clean startup/shutdown in noisy 12V systems with minimal external filtering. |
| Output Capacitor | Stable with ≥0.47µF ceramic - reduces BOM count and board space vs. legacy LDOs requiring ≥10µF tantalum. |
Pinout & Package
MPQ2013AGG-33-Z is housed in a thermally enhanced QFN-6 (2mm × 2mm) package with an exposed thermal pad. The package supports reflow soldering per JEDEC J-STD-020 and requires PCB land pattern per MPS drawing (1.90mm × 1.90mm pad, 0.65mm pitch).
| Pin/Terminal | Circuit Role | Design Meaning |
|---|---|---|
| 1 (IN) | Main power input | Accepts 2.5V–40V unregulated supply; requires local 1µF X5R/X7R ceramic decoupling. |
| 2 (EN) | Logic-enable control | Pull high to IN for automatic startup; pull low (<1.26V) to reduce supply current to <3µA. |
| 3 (GND) | Analog/digital ground reference | Must be tied to PCB ground plane; shares thermal path with exposed pad (Pin 3 = exposed pad). |
| 4 (FB) | Feedback reference node | Floating for fixed 3.3V version; internally biased to 1.215V; not used externally. |
| 5 (OUT) | Regulated output | Delivers 3.3V ±4% up to 150mA; requires ≥0.47µF ceramic capacitor directly at pin. |
| 6 (NC) | No connection | May be left open or grounded to improve thermal conduction; no electrical function. |
Key Features
| Feature | Design Value |
|---|---|
| AEC-Q100 Grade 1 qualification | Validated for −40°C to +125°C ambient operation with full parametric testing per automotive reliability standards. |
| Ultra-low quiescent current | 3.3µA typ. - enables continuous operation in vehicle body modules during sleep mode without draining battery. |
| Low-value output capacitor support | Stable with 0.47µF ceramic - eliminates large, aging-prone electrolytics and reduces footprint by >70% vs. legacy LDOs. |
| Integrated fault protection | Thermal shutdown + current limiting - prevents damage during short-circuit or thermal overload without external circuitry. |
| Wide input voltage range | 2.5V–40V - accommodates 12V/24V/42V automotive architectures and industrial 36V rails without external transients suppression. |
Applications
| Automotive Body Control Module (BCM) | Industrial Sensor Node |
|---|---|
Use Scenario: Powering CAN transceiver, LIN interface IC, and EEPROM in door module with 12V battery input subject to load dump and cold crank. IC Role / Device Role / Timing Role: Primary 3.3V LDO supplying digital logic and communication peripherals; handles input transients up to 40V. Use Value: 620mV dropout ensures uninterrupted operation during cranking (VIN ≥ 3.92V); AEC-Q100 qualification guarantees lifetime reliability under vibration and thermal cycling. | Use Scenario: Long-life wireless temperature/humidity sensor powered by primary lithium battery in remote factory monitoring. IC Role / Device Role / Timing Role: Always-on 3.3V regulator for MCU, RF SoC, and analog front-end; duty-cycled to extend battery life. Use Value: 3.3µA quiescent current enables >12-year battery life at 10µA average system current; QFN-6 footprint minimizes PCB area. |
| Medical Portable Diagnostic Device | Telematics Control Unit (TCU) Subsystem |
Use Scenario: Powering low-noise ADC, op-amps, and Bluetooth LE radio in handheld ultrasound probe operating from rechargeable Li-ion. IC Role / Device Role / Timing Role: Clean 3.3V rail for precision analog and RF sections; low PSRR noise contribution critical for signal fidelity. Use Value: Stable operation with 0.47µF ceramic output cap avoids ESR-related instability; 58dB PSRR at 100Hz suppresses battery ripple before ADC sampling. | Use Scenario: Supplying GPS/GNSS receiver, cellular modem, and secure MCU in automotive TCU with dual-battery backup. IC Role / Device Role / Timing Role: Secondary regulated rail derived from main 5V domain; must survive ISO 7637-2 pulse 5a (load dump). Use Value: 40V absolute max rating and integrated thermal shutdown prevent failure during load dump events; QFN-6 package enables compact layout near RF section. |
Equivalent & Alternatives
The following parts are listed as comparable options for similar fixed-output LDO applications.
| Alternative Part | Technical Difference | Application Difference | Selection Advice |
|---|---|---|---|
| MPQ2013AGQ-33-Z | QFN-8 (3mm×3mm) package; ±2% output accuracy; higher thermal dissipation (2.08W vs. 1.25W). | Better suited for higher ambient temperatures (>85°C) or sustained 150mA loads where QFN-6 thermal resistance (80°C/W) limits performance. | Select when thermal margin is constrained and PCB space permits larger footprint. |
| TLD1113-33ES | Infineon automotive LDO; 40V input; 150mA; ±2% accuracy; 1.8µA IQ; but only available in TO-252-3 package (larger, leaded). | Requires through-hole assembly or adapter; lacks QFN-6's thermal pad; lower IQ but no AEC-Q100 Grade 1 data in public docs. | Choose only if TO-252 mechanical mounting is mandatory and Grade 1 compliance is not required. |
Compared with MPQ2013AGQ-33-Z, the MPQ2013AGG-33-Z trades ±2% accuracy and higher thermal headroom for smaller footprint and lower cost; versus TLD1113-33ES, it offers superior thermal performance, surface-mount compatibility, and documented AEC-Q100 Grade 1 qualification - making it optimal for space-constrained automotive modules.
Availability
MPQ2013AGG-33-Z is available at Aetrix Electronics and suitable for automotive body electronics, industrial sensor networks, portable medical diagnostics, and telematics subsystems requiring stable component supply across extended temperature and lifecycle requirements.
Supply support for MPQ2013AGG-33-Z includes scheduled delivery planning, volume procurement assistance, BOM continuity management, traceable sourcing, and lifecycle availability coordination for OEM customers, industrial embedded developers, connected-device designers, and electronics production programs.
Manufacturer
Monolithic Power Systems (MPS) is a fabless semiconductor company specializing in high-performance analog and power ICs, with core expertise in DC/DC converters, LDOs, motor drivers, and LED drivers for automotive, industrial, and computing markets.
The MPQ2013A product line delivers ultra-low-IQ, wide-input linear regulators engineered specifically for AEC-Q100-compliant automotive subsystems and long-life battery-powered industrial endpoints where reliability and quiescent power dominate design priorities.
FAQ
What is the maximum allowable input voltage for MPQ2013AGG-33-Z?
The absolute maximum input voltage is +42V, but the recommended operating range is 2.5V to 40V. Operation above 40V risks permanent damage even for brief transients; external clamping (e.g., TVS diode) is advised for automotive load dump protection beyond 40V.
Can MPQ2013AGG-33-Z be used without an output capacitor?
No. A minimum 0.47µF X5R or X7R ceramic capacitor is required between OUT and GND for stability. Omitting it causes oscillation and potential device failure. Larger values (e.g., 4.7µF) improve load transient response but are not mandatory for basic regulation.
How does the EN pin behave during power-up?
The EN pin has hysteresis: it turns on when voltage rises above 1.48V and turns off when falling below 1.26V. Connecting EN directly to IN ensures automatic startup once VIN exceeds ~2.5V; no external pull-up is needed, and no external RC delay is required for sequencing.
Is the exposed thermal pad electrically connected?
Yes - the exposed pad (Pin 3) is internally connected to GND. It must be soldered to a PCB copper pour tied to the system ground plane to ensure both thermal dissipation (θJA = 80°C/W) and electrical integrity. Floating the pad degrades thermal performance and may cause instability.
What is the output voltage accuracy over temperature and load?
For MPQ2013AGG-33-Z, output voltage is guaranteed ±4% over −40°C to +125°C ambient and 0–150mA load. At TA = +25°C and IOUT = 0mA, accuracy tightens to ±3.4% (3.251V to 3.349V), per datasheet Table 6.
Does MPQ2013AGG-33-Z support reverse voltage protection?
No - the internal PMOS pass transistor includes a body diode that conducts from OUT to IN if VOUT > VIN. In backup-battery or dual-supply configurations, an external Schottky diode in series with IN is required to block reverse current and prevent damage.
MPQ2013AGG-33-Z Specifications
- Product attributes
- Attribute value
- Manufacturer:
- Monolithic Power Systems Inc.
- Series:
- -
- Package/Case:
- 6-VDFN Exposed Pad
- Packaging:
- Tape & Reel (TR)
- Product Status:
- Active
- Output Configuration:
- Positive
- Output Type:
- Fixed
- Number of Regulators:
- 1
- Voltage - Input (Max):
- 40V
- Voltage - Output (Min/Fixed):
- 3.3V
- Voltage - Output (Max):
- -
- Voltage Dropout (Max):
- 1.1V @ 150mA
- Current - Output:
- 150mA
- Current - Quiescent (Iq):
- 50 µA
- Current - Supply (Max):
- -
- PSRR:
- 58dB ~ 41dB (100Hz ~ 1kHz)
- Control Features:
- Enable
- Protection Features:
- Over Current, Over Temperature
- Operating Temperature:
- -40°C ~ 125°C (TJ)
- Grade:
- -
- Qualification:
- -
- Mounting Type:
- Surface Mount
- Supplier Device Package:
- 6-QFN (2x2)
MPQ2013AGG-33-Z FAQ
1.How can I place an order for MPQ2013AGG-33-Z through Aetrix?
Please submit a Request for Quotation (RFQ) for MPQ2013AGG-33-Z on Aetrix. Our sales agent will provide a competitive quotation and guide you through the order confirmation once you accept the terms.
2.Are the price and stock information for MPQ2013AGG-33-Z reliable?
The price and inventory of MPQ2013AGG-33-Z are updated periodically and may fluctuate due to market conditions. Stock and pricing data are typically refreshed every 24 hours. Quotation validity for MPQ2013AGG-33-Z is usually 5 days.
3.What payment methods are accepted for MPQ2013AGG-33-Z?
We accept Wire Transfer, PayPal, Credit Card, Western Union, MoneyGram, and Escrow for MPQ2013AGG-33-Z transactions.
Note: Certain payment methods may incur a processing fee.
4.How is shipping managed for MPQ2013AGG-33-Z?
MPQ2013AGG-33-Z orders can be shipped via leading logistics carriers, including DHL, UPS, FedEx, TNT, or Registered Mail.
Once your MPQ2013AGG-33-Z order is processed, you will receive an email with the shipment details and tracking number.
Note: Tracking information may take up to 24 hours to appear. Express delivery typically takes 3–5 business days.
5.How can I obtain technical support or documentation for MPQ2013AGG-33-Z?
For technical support, including MPQ2013AGG-33-Z datasheets, pinout diagrams, or application guidance, please contact our engineering support team. They can provide detailed documentation and assistance for your MPQ2013AGG-33-Z requirements.
6.How does Aetrix verify that MPQ2013AGG-33-Z is sourced from the original manufacturer or authorized distributors?
All MPQ2013AGG-33-Z products on Aetrix are procured from qualified distributors and authorized channels. Our dedicated quality assurance team conducts strict verification, including traceability checks and, if necessary, third-party testing. This ensures that MPQ2013AGG-33-Z meets industry standards.
7.What is the process for return or replacement of MPQ2013AGG-33-Z?
All MPQ2013AGG-33-Z units undergo pre-shipment inspection (PSI). If there is an issue with MPQ2013AGG-33-Z, returns or replacements are accepted under the following conditions:
1.Quantity discrepancies, incorrect items, or visible external defects (such as breakage or corrosion), acknowledged by Aetrix.
2.The issue is reported within 90 days of delivery.
3.The MPQ2013AGG-33-Z part is unused and in its original packaging.
Return procedure for MPQ2013AGG-33-Z:
1.Submit a request within 90 days.
2.Obtain a Return Material Authorization (RMA) from Aetrix.
MPQ2013AGG-33-Z Tags
-
MIC5504-1.8YM5-TR
Microchip Technology
-
MIC5504-3.3YM5-TR
Microchip Technology
-
MIC5365-3.0YC5-TR
Microchip Technology
-
MIC5365-1.8YC5-TR
Microchip Technology
-
MIC5365-2.5YC5-TR
Microchip Technology
-
MIC5365-3.3YC5-TR
Microchip Technology
-
MIC5365-3.3YD5-TR
Microchip Technology
-
MIC5317-3.3YM5-TR
Microchip Technology
-
TLV1117LV33DCYR
Texas Instruments
-
MIC5317-3.3YMT-TZ
Microchip Technology
-
MIC5528-3.3YMT-TR
Microchip Technology
-
TLV75801PDRVR
Texas Instruments
Tech Hub
A D latch stores one bit while Enable controls when data can pass. This reference covers gate-level operation, truth tables, transparency, setup and hold timing, LE versus OE, common ICs and practical …
An SR latch stores one bit through cross-coupled feedback. This engineering reference covers NOR and NAND implementations, truth tables, forbidden-state recovery, gated operation, switch debouncing, fa…
Latch circuits retain one bit through feedback. This technical reference covers SR and D latches, truth tables, transparency, timing limits, latch-versus-flip-flop behavior, applications and common log…
An engineering guide to LED driver operation, constant-current and constant-voltage outputs, linear and switching topologies, dimming, IC selection, calculations, replacement compatibility, and fault c…
Operational amplifier guide covering op amp basics, feedback, ideal vs real op amps, common configurations, buffer circuits, offset, bias current, gain-bandwidth, slew rate, rail-to-rail limits and sel…
Jumper cables guide covering safe connection order, red and black clamp placement, final ground connection, cable gauge, length, clamp quality, copper vs CCA cables, jump starter comparison and battery…
LDO regulator guide covering low dropout voltage, power dissipation, thermal design, PSRR, output noise, capacitor stability, adjustable LDO circuits, LDO vs buck converter and datasheet selection chec…
Conditional Access Module guide covering CAM meaning, CI/CI+ interface, smart card authorization, DVB security workflow, TV and set-top box compatibility, internal electronics, ESD protection, connecto…
Guide to electronic component obsolescence covering EOL risk, PCN/PDN notices, last-time buy planning, replacement options, form-fit-function validation, counterfeit risk and BOM lifecycle management.
18650 battery guide covering lithium-ion cell basics, 3.6V/3.7V voltage, 4.2V charging, mAh and Wh capacity, protected cells, chargers, BMS, series-parallel packs, holders, welding and sourcing checks.…
