My Inquiry
My Account
NXP Semiconductors MPX2053GVP
- Part No.:
- MPX2053GVP
- Manufacturer:
- NXP Semiconductors
- Category:
- Pressure Sensors, Transducers
- Package:
- 4-SIP Module
- Datasheet:
-
MPX2053GVP.pdf
- Description:
- SENSOR 7.25PSIG 0.19" .04V
- Quantity:
- Payment:
- Shipping:
Inventory:1,420
Please send an inquiry. Send us your inquiry, and we will respond immediately.
Product details
Overview
MPX2053GVP from NXP Semiconductors is a silicon piezoresistive gauge pressure sensor delivering a ratiometric, temperature-compensated analog voltage output proportional to applied pressure. It operates over 0–50 kPa (0–7.25 PSI), features ±0.4% VFSS linearity, ±0.1% VFSS pressure hysteresis, and is calibrated for 0 °C to 85 °C operation. Used in medical diagnostics and pump/motor controllers where stable low-range pressure sensing is required.
For engineers reviewing the MPX2053GVP datasheet, MPX2053GVP pinout, MPX2053GVP application, or MPX2053GVP equivalent, this page provides verified technical context, pin-level circuit roles, real-world use-value mapping, and validated alternative options for differential/gauge pressure measurement systems requiring <50 kPa full-scale range and on-chip temperature compensation.
Technical Context
The MPX2053GVP integrates a monolithic silicon diaphragm with embedded strain gauges and thin-film resistor networks for direct piezoresistive transduction. Its output is ratiometric to supply voltage (VS = 10–16 Vdc), enabling stable measurements without external reference voltage dependency.
On-chip laser trimming delivers factory calibration for span, offset, and temperature coefficients across 0 °C to 85 °C - achieving TCVFSS ≤ ±2.0% VFSS and TCVoff ≤ ±1.0 mV. The device supports differential or gauge configurations, with P1 side identified by stainless steel cap (Unibody) or port attachment (MPAK).
Key Specifications
| Parameter | Value and Actual Design Meaning |
|---|---|
| Pressure Range | 0–50 kPa gauge; enables precise low-pressure monitoring in medical and industrial fluid control. |
| Output Type | Differential analog voltage (±VOUT); provides noise-immune signal transmission over PCB traces. |
| Full Scale Span | 38.5–41.5 mV at VS = 10 Vdc; defines usable output swing for ADC interface scaling. |
| Linearity Error | ±0.4% VFSS (end-point method); ensures predictable error budget in closed-loop pressure regulation. |
| Temp Compensation | 0 °C to 85 °C; eliminates need for external temperature compensation circuitry in ambient environments. |
| Response Time | 1.0 ms (10%–90%); supports dynamic pressure tracking in motor/pump transient events. |
| Supply Voltage | 10–16 Vdc; compatible with standard industrial power rails and tolerant of minor rail variation. |
Pinout & Package
MPX2053GVP uses the Unibody package (Case 344-15), featuring a stainless steel cap on the P1 (pressure) side and epoxy-sealed lead frame. This hermetic construction ensures long-term reliability in humid or mildly aggressive media when used with dry clean air.
| Pin/Terminal | Circuit Role | Design Meaning |
|---|---|---|
| GND | Reference ground | Common return path for supply and output; must be low-impedance to minimize offset drift. |
| +VOUT | Positive output terminal | Delivers voltage proportional to P1–P2 pressure differential; connects to instrumentation amplifier +IN. |
| VS | Power supply input | Excitation source for ratiometric operation; output scales linearly with VS variation. |
| –VOUT | Negative output terminal | Completes differential output pair; enables common-mode rejection in noisy environments. |
Key Features
| Feature | Design Value |
|---|---|
| Ratiometric output | Output voltage scales directly with VS; removes dependency on precision voltage references in system design. |
| On-chip temperature compensation | Calibrated over 0 °C to 85 °C; eliminates external thermistor networks and software correction tables. |
| Laser-trimmed span/offset | Factory-set accuracy without user calibration; reduces production test time and BOM count. |
| Differential voltage output | ±VOUT architecture rejects common-mode noise; improves SNR in electrically noisy pump/motor environments. |
| Stainless steel P1 cap | Robust mechanical interface for direct media contact; enables integration into compact medical housings. |
Applications
| Medical Diagnostics | Pump/Motor Controllers |
|---|---|
Use Scenario: Non-invasive blood pressure measurement in portable sphygmomanometers. IC Role / Device Role / Timing Role: Gauge pressure transducer measuring cuff inflation pressure relative to atmosphere. Use Value: ±0.1% VFSS pressure hysteresis ensures repeatable readings across multiple inflation-deflation cycles. |
Use Scenario: Closed-loop pressure feedback in HVAC condensate pumps. IC Role / Device Role / Timing Role: Real-time differential pressure monitor detecting clogged filter or blocked outlet. Use Value: 1.0 ms response time enables rapid fault detection before motor thermal shutdown occurs. |
| Level Indicators | Robotics |
Use Scenario: Liquid level sensing in chemical dosing tanks via hydrostatic head pressure. IC Role / Device Role / Timing Role: Low-range gauge sensor converting column height (kPa) to calibrated voltage. Use Value: 0–50 kPa range matches typical 0–5 m water column; avoids signal saturation at full scale. |
Use Scenario: End-effector force feedback in collaborative robotic grippers. IC Role / Device Role / Timing Role: Embedded pressure interface detecting object contact and grip force magnitude. Use Value: Ratiometric output maintains accuracy across battery-voltage droop during mobile robot operation. |
Equivalent & Alternatives
The following parts are listed as comparable options for similar gauge pressure sensing applications.
| Alternative Part | Technical Difference | Application Difference | Selection Advice |
|---|---|---|---|
| MPXV2053DP | Small Outline Package (Case 1351), 8-pin SOIC footprint; identical electrical specs but different mechanical interface. | Requires PCB layout change for surface-mount assembly; lacks stainless steel cap, uses marking-side P1 identification. | Select when automated SMT placement is prioritized and media isolation is handled externally. |
| MPXM2053GS | MPAK package (Case 1320A-02), same 4-pin configuration and pinout; includes port for tubing connection. | Better suited for pneumatic hose coupling in portable medical devices; same electrical performance and temp range. | Choose for applications needing direct tubing interface without custom manifold design. |
Compared with MPX2053GVP, MPXV2053DP offers SMT compatibility at the cost of reduced media robustness, while MPXM2053GS retains the same pinout and performance but adds a molded port for simplified fluidic integration - making it ideal for handheld diagnostic tools.
Availability
MPX2053GVP is available at Aetrix Electronics and suitable for medical diagnostics, pump/motor controllers, level indicators, and robotics requiring stable component supply with guaranteed traceability and lifecycle continuity.
Supply support for MPX2053GVP includes scheduled delivery planning, volume procurement assistance, BOM continuity management, traceable sourcing, and lifecycle availability coordination for OEM customers, industrial embedded developers, connected-device designers, and electronics production programs.
Manufacturer
NXP Semiconductors is a global semiconductor company specializing in secure connectivity solutions for automotive, industrial, and IoT applications, with deep expertise in sensor signal conditioning and mixed-signal IC design.
The MPX2053 series belongs to NXP's legacy pressure sensor product line, engineered specifically for high-accuracy, low-drift gauge and differential pressure measurement in medical, industrial, and consumer equipment operating below 100 kPa.
FAQ
What is the pressure type supported by MPX2053GVP?
The MPX2053GVP is a gauge pressure sensor, meaning it measures pressure relative to ambient atmospheric pressure. Its P1 side (stainless steel cap) interfaces with the measured medium, while P2 is vented to atmosphere. It is not rated for absolute or sealed-gauge configurations, and its specified 0–50 kPa range assumes P2 = atmospheric pressure.
Does MPX2053GVP require external temperature compensation?
No, MPX2053GVP does not require external temperature compensation. It incorporates on-chip temperature compensation calibrated over 0 °C to 85 °C, with TCVFSS ≤ ±2.0% VFSS and TCVoff ≤ ±1.0 mV. This eliminates the need for external thermistors or software correction algorithms in most ambient-temperature applications.
What is the supply voltage range for reliable operation of MPX2053GVP?
The MPX2053GVP operates reliably with a supply voltage (VS) between 10 Vdc and 16 Vdc. Operation outside this range may induce self-heating errors or violate absolute maximum ratings. At VS = 10 Vdc, full-scale output is 38.5–41.5 mV; output remains ratiometric, scaling linearly with VS within the specified range.
Can MPX2053GVP be used with dry clean air only?
Yes - MPX2053GVP's qualification and published specifications assume dry clean air as the pressure medium. Use with other media (e.g., moisture-laden air, oils, or corrosive gases) may degrade long-term stability or cause failure. For alternate media, consult NXP Application Note AN3728 and contact NXP for compatibility validation before deployment.
What is the pinout configuration of MPX2053GVP and how is it verified?
MPX2053GVP uses a 4-pin Unibody package (Case 344-15) with pins: 1 = GND, 2 = +VOUT, 3 = VS, 4 = –VOUT. This pinout is confirmed in Section 6.1 of the official NXP MPX2053 datasheet Rev. 11 (2021), Figure 2 and Table 2, and matches MPX2053D - the base Unibody variant from which MPX2053GVP is derived.
MPX2053GVP Specifications
- Product attributes
- Attribute value
- Manufacturer:
- NXP Semiconductors
- Series:
- MPX2053
- Package/Case:
- 4-SIP Module
- Packaging:
- Tray
- Product Status:
- Obsolete
- Applications:
- Board Mount
- Pressure Type:
- Vented Gauge
- Operating Pressure:
- 7.25PSI (50kPa)
- Output Type:
- Wheatstone Bridge
- Output:
- 0 mV ~ 40 mV (10V)
- Accuracy:
- -
- Voltage - Supply:
- 10V ~ 16V
- Port Size:
- Male - 0.19" (4.93mm) Tube
- Port Style:
- Barbed
- Features:
- Temperature Compensated
- Termination Style:
- PC Pin
- Maximum Pressure:
- 29.01PSI (200kPa)
- Operating Temperature:
- -40°C ~ 125°C
- Grade:
- -
- Qualification:
- -
- Mounting Type:
- Through Hole
- Supplier Device Package:
- -
MPX2053GVP FAQ
1.How can I place an order for MPX2053GVP through Aetrix?
Please submit a Request for Quotation (RFQ) for MPX2053GVP on Aetrix. Our sales agent will provide a competitive quotation and guide you through the order confirmation once you accept the terms.
2.Are the price and stock information for MPX2053GVP reliable?
The price and inventory of MPX2053GVP are updated periodically and may fluctuate due to market conditions. Stock and pricing data are typically refreshed every 24 hours. Quotation validity for MPX2053GVP is usually 5 days.
3.What payment methods are accepted for MPX2053GVP?
We accept Wire Transfer, PayPal, Credit Card, Western Union, MoneyGram, and Escrow for MPX2053GVP transactions.
Note: Certain payment methods may incur a processing fee.
4.How is shipping managed for MPX2053GVP?
MPX2053GVP orders can be shipped via leading logistics carriers, including DHL, UPS, FedEx, TNT, or Registered Mail.
Once your MPX2053GVP order is processed, you will receive an email with the shipment details and tracking number.
Note: Tracking information may take up to 24 hours to appear. Express delivery typically takes 3–5 business days.
5.How can I obtain technical support or documentation for MPX2053GVP?
For technical support, including MPX2053GVP datasheets, pinout diagrams, or application guidance, please contact our engineering support team. They can provide detailed documentation and assistance for your MPX2053GVP requirements.
6.How does Aetrix verify that MPX2053GVP is sourced from the original manufacturer or authorized distributors?
All MPX2053GVP products on Aetrix are procured from qualified distributors and authorized channels. Our dedicated quality assurance team conducts strict verification, including traceability checks and, if necessary, third-party testing. This ensures that MPX2053GVP meets industry standards.
7.What is the process for return or replacement of MPX2053GVP?
All MPX2053GVP units undergo pre-shipment inspection (PSI). If there is an issue with MPX2053GVP, returns or replacements are accepted under the following conditions:
1.Quantity discrepancies, incorrect items, or visible external defects (such as breakage or corrosion), acknowledged by Aetrix.
2.The issue is reported within 90 days of delivery.
3.The MPX2053GVP part is unused and in its original packaging.
Return procedure for MPX2053GVP:
1.Submit a request within 90 days.
2.Obtain a Return Material Authorization (RMA) from Aetrix.
MPX2053GVP Tags
-
DPS368XTSA1
Infineon Technologies
-
DPS310XTSA1
Infineon Technologies
-
LPS22HHTR
STMicroelectronics
-
ICP-20100
TDK InvenSense
-
ICP-10110
TDK InvenSense
-
LPS22DFTR
STMicroelectronics
-
LPS22HBTR
STMicroelectronics
-
BMP390
Bosch Sensortec
-
BMP581
Bosch Sensortec
-
BMP384
Bosch Sensortec
-
2511020213301
Würth Elektronik
-
ILPS22QSTR
STMicroelectronics
Tech Hub
A practical engineering guide to 3.3V and 5V logic compatibility, input thresholds, resistor dividers, translator ICs, MOSFET level shifting, I2C pull-ups, timing limits and power-sequencing risks.
The 74HC595 uses push-pull logic outputs, while the TPIC6B595 uses 50 V open-drain DMOS sinks for higher-power loads. This guide compares timing, current limits, 3.3 V interfacing, load wiring, thermal…
The 74HC595 converts serial data into eight stable parallel outputs. This guide covers pin functions, shift and storage timing, OE and MR behavior, drive-current limits, cascading, voltage compatibilit…
A technical comparison of level-sensitive latches and edge-triggered flip-flops, covering timing windows, setup and hold limits, master–slave operation, time borrowing, race-through, HDL inference and…
A D latch stores one bit while Enable controls when data can pass. This reference covers gate-level operation, truth tables, transparency, setup and hold timing, LE versus OE, common ICs and practical …
An SR latch stores one bit through cross-coupled feedback. This engineering reference covers NOR and NAND implementations, truth tables, forbidden-state recovery, gated operation, switch debouncing, fa…
Latch circuits retain one bit through feedback. This technical reference covers SR and D latches, truth tables, transparency, timing limits, latch-versus-flip-flop behavior, applications and common log…
An engineering guide to LED driver operation, constant-current and constant-voltage outputs, linear and switching topologies, dimming, IC selection, calculations, replacement compatibility, and fault c…
Operational amplifier guide covering op amp basics, feedback, ideal vs real op amps, common configurations, buffer circuits, offset, bias current, gain-bandwidth, slew rate, rail-to-rail limits and sel…
Jumper cables guide covering safe connection order, red and black clamp placement, final ground connection, cable gauge, length, clamp quality, copper vs CCA cables, jump starter comparison and battery…
