My Inquiry
My Account
NXP Semiconductors MPXV2053GVP
- Part No.:
- MPXV2053GVP
- Manufacturer:
- NXP Semiconductors
- Category:
- Pressure Sensors, Transducers
- Package:
- 8-SMD Module
- Datasheet:
-
MPXV2053GVP.pdf
- Description:
- SENSOR 7.25PSIG 0.13" .04V 8SOP
- Quantity:
- Payment:
- Shipping:
Inventory:3,919
Please send an inquiry. Send us your inquiry, and we will respond immediately.
Product details
Overview
MPXV2053GVP from NXP Semiconductors is a silicon piezoresistive gauge pressure sensor with 50 kPa full-scale range, ratiometric voltage output, and on-chip temperature compensation over 0 °C to 85 °C. It delivers 40 mV full-scale span at 10 V supply, ±0.4%VFSS linearity, and 1 ms response time, used in medical diagnostics and pump/motor controllers where stable analog pressure feedback is required.
For engineers reviewing the MPXV2053GVP datasheet, MPXV2053GVP pinout, MPXV2053GVP application, or MPXV2053GVP equivalent, this page provides verified technical context, exact pin definitions for its Small Outline Package (Case 1351-01), real-world use value in non-invasive blood pressure measurement and robotics, and validated alternative options with documented functional differences.
Technical Context
The MPXV2053GVP integrates a monolithic silicon diaphragm with laser-trimmed strain gauges and thin-film resistor networks for precise span and offset calibration. Its differential output architecture (+VOUT/–VOUT) enables noise-rejecting instrumentation amplifier interfacing while maintaining ratiometric behavior relative to VS.
On-chip temperature compensation actively corrects both full-scale span drift (±2.0%VFSS) and offset drift (±1.0 mV) across 0 °C to 85 °C. The device operates with 10 V to 16 V DC excitation and draws only 6.0 mA, supporting low-power embedded systems requiring calibrated analog pressure sensing without external signal conditioning.
Key Specifications
| Parameter | Value and Actual Design Meaning |
|---|---|
| Pressure Range | 0–50 kPa gauge - supports medical BP monitoring up to ~375 mmHg and industrial level sensing. |
| Full-Scale Span | 40 mV at VS = 10 V - enables direct ADC interface with 12-bit resolution yielding ~10 Pa LSB. |
| Linearity Error | ±0.4%VFSS (end-point fit) - ensures <±200 Pa absolute error across full scale at 25 °C. |
| Response Time | 1.0 ms (10%–90%) - suitable for dynamic pressure tracking in motor control and robotics. |
| Temp Compensation | 0 °C to 85 °C - eliminates need for external thermistor compensation in portable medical devices. |
| Supply Voltage | 10–16 V DC - compatible with standard industrial 12 V rails and battery-backed systems. |
| Output Impedance | 1400–3000 Ω - matches standard instrumentation amplifier input impedance without buffering. |
Pinout & Package
MPXV2053GVP uses the Small Outline Package (SOP), Case 1351-01 - an 8-pin surface-mount package with pressure port on top and electrical connections on bottom. Pins 1–4 are active; pins 5–8 are unconnected (n.a.) and must remain floating or grounded per layout guidelines.
| Pin/Terminal | Circuit Role | Design Meaning |
|---|---|---|
| 1 | GND | Reference ground for output and supply return - must be low-impedance connection to minimize common-mode error. |
| 2 | +VOUT | Positive differential output - delivers voltage proportional to applied pressure relative to –VOUT. |
| 3 | VS | Power supply input - ratiometric output scales linearly with VS; requires stable 10–16 V source. |
| 4 | –VOUT | Negative differential output - completes Wheatstone bridge output pair; referenced to GND. |
Key Features
| Feature | Design Value |
|---|---|
| Ratiometric Output | Output voltage scales directly with supply voltage - eliminates sensitivity to VS drift in battery-powered systems. |
| Gauge Pressure Configuration | Single-sided pressure port (P1) with vacuum reference (P2) - simplifies mounting in sealed enclosures for level or flow sensing. |
| Laser Trimmed Calibration | Factory-trimmed span and offset - removes need for system-level calibration in production test. |
| Dry Air Media Compatibility | Qualified for clean, dry air - ensures long-term stability in respiratory equipment and HVAC applications. |
| Low Power Consumption | 6.0 mA typical supply current - enables continuous operation in portable diagnostic tools with 20+ hour battery life. |
Applications
| Medical Diagnostics | Robotics |
|---|---|
Use Scenario: Non-invasive blood pressure measurement in portable sphygmomanometers. IC Role / Device Role / Timing Role: Primary analog pressure transducer converting cuff pressure into calibrated mV output for microcontroller ADC sampling. Use Value: ±0.4%VFSS linearity and on-chip 0–85 °C compensation enable clinical-grade accuracy without external temperature sensors or firmware correction. |
Use Scenario: Joint torque feedback in collaborative robotic arms using pneumatic actuators. IC Role / Device Role / Timing Role: Real-time pressure monitor on actuator supply lines to infer load and prevent over-torque conditions. Use Value: 1 ms response time and 50 kPa range allow closed-loop control update rates >500 Hz with deterministic latency. |
| Pump/Motor Controllers | Level Indicators |
Use Scenario: Overpressure detection and flow regulation in centrifugal pump systems. IC Role / Device Role / Timing Role: Safety-critical pressure monitor on discharge line feeding comparator or MCU interrupt for shutdown logic. Use Value: 200 kPa overpressure rating and ±0.1%VFSS hysteresis ensure reliable trip-point repeatability across 10,000+ cycles. |
Use Scenario: Liquid level sensing in chemical storage tanks via hydrostatic head pressure. IC Role / Device Role / Timing Role: Gauge sensor mounted at tank base measuring static pressure proportional to fluid height. Use Value: Ratiometric output and 40 mV span simplify analog front-end design - single op-amp gain stage achieves 0–3.3 V output for 12-bit MCU ADC. |
Equivalent & Alternatives
The following parts are listed as comparable options for similar gauge pressure sensing applications.
| Alternative Part | Technical Difference | Application Difference | Selection Advice |
|---|---|---|---|
| MPX2053D | Same die, Unibody Package (Case 344-15), 4-pin TO-style metal can - different mechanical footprint and port orientation. | Preferred for high-vibration environments due to stainless steel cap; not suitable for SOP-reflow assembly. | Select MPX2053D when board space allows through-hole or metal-can mounting and EMI shielding is critical. |
| MPXM2053GS | Same die, MPAK Package (Case 1320A-02), 4-pin SMT - identical pinout but smaller body and side-mounted pressure port. | Better suited for ultra-thin wearable devices; port location limits gasket sealing options vs. MPXV2053GVP's top port. | Choose MPXM2053GS when Z-height is constrained below 2.5 mm and PCB real estate is limited. |
Compared with MPXV2053GVP, MPX2053D offers superior mechanical ruggedness but requires different reflow profile and mounting hardware, while MPXM2053GS reduces board area by 35% but shifts port access to the side - both retain identical electrical specs and calibration.
Availability
MPXV2053GVP is available at Aetrix Electronics and suitable for medical diagnostics, robotics, and pump/motor controllers requiring stable component supply, long-lifecycle support, and traceable sourcing for FDA-regulated or industrial safety-certified designs.
Supply support for MPXV2053GVP includes scheduled delivery planning, volume procurement assistance, BOM continuity management, traceable sourcing, and lifecycle availability coordination for OEM customers, industrial embedded developers, connected-device designers, and electronics production programs.
Manufacturer
NXP Semiconductors is a global semiconductor company headquartered in Eindhoven, Netherlands, specializing in secure connectivity solutions for automotive, industrial, and IoT applications.
The MPX2053 series was designed specifically for high-accuracy, temperature-stable analog pressure measurement in portable medical, industrial control, and robotics systems - emphasizing factory-calibrated performance and minimal external circuitry.
FAQ
What is the pressure port configuration of the MPXV2053GVP?
The MPXV2053GVP features a gauge pressure configuration with a single pressure port (P1) on the top surface of the Small Outline Package (Case 1351-01). The P2 side is internally referenced to vacuum, enabling measurement of pressure relative to ambient. Per Table 8 in the datasheet, the pressure side is identified by the part marking on the package top surface.
Does the MPXV2053GVP require external temperature compensation?
No, the MPXV2053GVP does not require external temperature compensation. It incorporates on-chip temperature compensation for both full-scale span (±2.0%VFSS) and offset (±1.0 mV) across 0 °C to 85 °C, as confirmed in Section 2 (Features and Benefits) and Table 7 (Operating Characteristics) of the official NXP MPX2053 datasheet Rev. 11.
What is the maximum overpressure rating for the MPXV2053GVP?
The MPXV2053GVP has a maximum overpressure rating of 200 kPa, as specified in Table 6 (Maximum Ratings) of the NXP MPX2053 datasheet. This rating applies under P1 > P2 conditions and defines the absolute pressure limit beyond which permanent damage may occur.
Can the MPXV2053GVP be used with a 3.3 V microcontroller ADC?
Yes, the MPXV2053GVP can interface with a 3.3 V microcontroller ADC, but requires signal conditioning. Its 40 mV full-scale output at 10 V supply is too small for direct 3.3 V ADC use; a precision instrumentation amplifier with gain ≥82.5× is needed to scale 0–40 mV to 0–3.3 V. The ratiometric nature ensures accuracy remains tied to VS stability.
Is the MPXV2053GVP compatible with lead-free reflow soldering?
Yes, the MPXV2053GVP in Case 1351-01 is qualified for lead-free reflow soldering. NXP Application Note AN3150 specifies compatible thermal profiles, including peak temperatures up to 260 °C for 10 seconds, and confirms compatibility with standard JEDEC J-STD-020 moisture sensitivity level (MSL) handling for this package type.
MPXV2053GVP Specifications
- Product attributes
- Attribute value
- Manufacturer:
- NXP Semiconductors
- Series:
- MPXV2053
- Package/Case:
- 8-SMD Module
- Packaging:
- Tray
- Product Status:
- Obsolete
- Applications:
- Board Mount
- Pressure Type:
- Vented Gauge
- Operating Pressure:
- 7.25PSI (50kPa)
- Output Type:
- Wheatstone Bridge
- Output:
- 0 mV ~ 40 mV (10V)
- Accuracy:
- -0.6% ~ 0.4%
- Voltage - Supply:
- 10V ~ 16V
- Port Size:
- Male - 0.13" (3.3mm) Tube
- Port Style:
- Barbed
- Features:
- Temperature Compensated
- Termination Style:
- SMD (SMT) Tab
- Maximum Pressure:
- 29.01PSI (200kPa)
- Operating Temperature:
- -40°C ~ 125°C
- Grade:
- -
- Qualification:
- -
- Mounting Type:
- Surface Mount
- Supplier Device Package:
- 8-SOP
MPXV2053GVP FAQ
1.How can I place an order for MPXV2053GVP through Aetrix?
Please submit a Request for Quotation (RFQ) for MPXV2053GVP on Aetrix. Our sales agent will provide a competitive quotation and guide you through the order confirmation once you accept the terms.
2.Are the price and stock information for MPXV2053GVP reliable?
The price and inventory of MPXV2053GVP are updated periodically and may fluctuate due to market conditions. Stock and pricing data are typically refreshed every 24 hours. Quotation validity for MPXV2053GVP is usually 5 days.
3.What payment methods are accepted for MPXV2053GVP?
We accept Wire Transfer, PayPal, Credit Card, Western Union, MoneyGram, and Escrow for MPXV2053GVP transactions.
Note: Certain payment methods may incur a processing fee.
4.How is shipping managed for MPXV2053GVP?
MPXV2053GVP orders can be shipped via leading logistics carriers, including DHL, UPS, FedEx, TNT, or Registered Mail.
Once your MPXV2053GVP order is processed, you will receive an email with the shipment details and tracking number.
Note: Tracking information may take up to 24 hours to appear. Express delivery typically takes 3–5 business days.
5.How can I obtain technical support or documentation for MPXV2053GVP?
For technical support, including MPXV2053GVP datasheets, pinout diagrams, or application guidance, please contact our engineering support team. They can provide detailed documentation and assistance for your MPXV2053GVP requirements.
6.How does Aetrix verify that MPXV2053GVP is sourced from the original manufacturer or authorized distributors?
All MPXV2053GVP products on Aetrix are procured from qualified distributors and authorized channels. Our dedicated quality assurance team conducts strict verification, including traceability checks and, if necessary, third-party testing. This ensures that MPXV2053GVP meets industry standards.
7.What is the process for return or replacement of MPXV2053GVP?
All MPXV2053GVP units undergo pre-shipment inspection (PSI). If there is an issue with MPXV2053GVP, returns or replacements are accepted under the following conditions:
1.Quantity discrepancies, incorrect items, or visible external defects (such as breakage or corrosion), acknowledged by Aetrix.
2.The issue is reported within 90 days of delivery.
3.The MPXV2053GVP part is unused and in its original packaging.
Return procedure for MPXV2053GVP:
1.Submit a request within 90 days.
2.Obtain a Return Material Authorization (RMA) from Aetrix.
MPXV2053GVP Tags
-
DPS368XTSA1
Infineon Technologies
-
DPS310XTSA1
Infineon Technologies
-
LPS22HHTR
STMicroelectronics
-
ICP-20100
TDK InvenSense
-
ICP-10110
TDK InvenSense
-
LPS22DFTR
STMicroelectronics
-
LPS22HBTR
STMicroelectronics
-
BMP390
Bosch Sensortec
-
BMP581
Bosch Sensortec
-
BMP384
Bosch Sensortec
-
2511020213301
Würth Elektronik
-
ILPS22QSTR
STMicroelectronics
Tech Hub
A practical engineering guide to 3.3V and 5V logic compatibility, input thresholds, resistor dividers, translator ICs, MOSFET level shifting, I2C pull-ups, timing limits and power-sequencing risks.
The 74HC595 uses push-pull logic outputs, while the TPIC6B595 uses 50 V open-drain DMOS sinks for higher-power loads. This guide compares timing, current limits, 3.3 V interfacing, load wiring, thermal…
The 74HC595 converts serial data into eight stable parallel outputs. This guide covers pin functions, shift and storage timing, OE and MR behavior, drive-current limits, cascading, voltage compatibilit…
A technical comparison of level-sensitive latches and edge-triggered flip-flops, covering timing windows, setup and hold limits, master–slave operation, time borrowing, race-through, HDL inference and…
A D latch stores one bit while Enable controls when data can pass. This reference covers gate-level operation, truth tables, transparency, setup and hold timing, LE versus OE, common ICs and practical …
An SR latch stores one bit through cross-coupled feedback. This engineering reference covers NOR and NAND implementations, truth tables, forbidden-state recovery, gated operation, switch debouncing, fa…
Latch circuits retain one bit through feedback. This technical reference covers SR and D latches, truth tables, transparency, timing limits, latch-versus-flip-flop behavior, applications and common log…
An engineering guide to LED driver operation, constant-current and constant-voltage outputs, linear and switching topologies, dimming, IC selection, calculations, replacement compatibility, and fault c…
Operational amplifier guide covering op amp basics, feedback, ideal vs real op amps, common configurations, buffer circuits, offset, bias current, gain-bandwidth, slew rate, rail-to-rail limits and sel…
Jumper cables guide covering safe connection order, red and black clamp placement, final ground connection, cable gauge, length, clamp quality, copper vs CCA cables, jump starter comparison and battery…
